AC Distributor GooglePlus
Flags
Flags
Facebook

Handheld Hydraulic Construction Equipment

Handheld Hammer in Use

Powerful, lightweight, and portable

AWDS Logo

Hammers/Breakers Drain Pumps
Core Drills Post Equipment
Cut-off Saws Power Packs

Handheld Hammers in use

The best power-to-weight

Construction and rental companies around the world are discovering the advantages of using hydraulics. They know that hydraulic equipment offers the best power-to-weight ratio of any system. And they appreciate that a hydraulic power pack is small and light enough so that two people can lift one up and fit it in the back of a van.

A real cost advantage

Construction and rental companies have been quick to understand the very real cost advantage of hydraulics. For the price of one compressor/breaker combination, you can buy two complete hydraulic power pack/breaker sets. In fact, you might not need a power pack at all. With the help of an oil flow divider and an extension hose, you can hook hydraulic tools directly to a hydraulic-powered carrier.

Hydraulics hit harder

The first time you use a hydraulic breaker, you're in for a surprise. Here's this compact, quiet tool...and it hits harder than any other type of breaker. That's because hydraulics are more efficient than electric, pneumatic, or gas-powered tools. For example, a 70 lb. hydraulic breaker gives you the same hitting power as a 90 lb. pneumatic. Thanks to their amazing impact energy, hydraulic breakers can be used on concrete, asphalt, and frozen ground. You can, of course, also use them for trenching, tie-tamping, spike driving, and general demolition.

Easy to own

There's not much that can go wrong with an Atlas Copco hydraulic breaker. With just two moving parts, there's minimal wear and very few parts to replace. Hydraulics are reliable by nature. Working in a closed loop, dirt and moisture are kept out. And due to the no-spill, flat-face couplings, it's easy to keep the system clean.

High Back Pressure Applications

Some hydraulic-powered carriers have internal system pressures that preclude the use of hydraulic tools. For these applications, Atlas Copco has developed high back pressure units to use in conjunction with flow dividers.

A harder hitting hammer

LH 11

Powerful horizontal pick hammer

This D-handle breaker is ideal for horizontal work in brick, mortar, and light concrete. It is one of the most powerful pick hammers on the market, featuring an impact energy of 18 foot pounds and impact rate of 2,400 blows/min. With its detachable front handle, the LH 11 is a popular choice for renovation, demolition, and structural alteration jobs.

LH 11 Horizontal Pick Hammer
 

 

 

Front handle

Front handle

The front handle, which is available as an optional extra for the LH 11, helps to increase control and reduce fatigue. It pivots 360° for optimal positioning and is easy to detach.

 
 

Pick hammer
LH 11
Shank size
Hex (in.)

7/8 x 3 1/4

Weight
lb.
24.0
Length
in.
23.6
Oil flow
gpm
5.3
Working pressure
psi
1000 - 1300
Return line pressure max
psi
150
Vibration level (ISO 8662-5)
H/A
10.1
Impact rate (5 gpm)
blows/min.
2400
EHTMA class
C

A complete line of T-handle breakers

T-handle Breakers in use

LH 18/19 E
Lightweight, multipurpose breakers

Used to break brickwork, frozen soil, asphalt concrete, as well as for tamping and compaction.

Delivering 48 foot pounds at 1,600 blows/min., the LH 18 and 19 E are very effective tools.

The breakers are popular with contractors and rental companies for indoor and outdoor renovation and demolition jobs.

And they are the preferred choice for major railroad companies.

 

LH 22/23 E
Medium weight, multipurpose breakers

Among the best general purpose medium weight breakers available in the 50 - 62 lb. range, the LH22/23 E are used by leading rental companies around the world.

These breakers are commonly used with a 5" asphalt chisel for road building and maintenance applications, but also work well in brickwork, frozen soil, and concrete.

Can be used with 5 - 8 gpm power packs.

LH 27/28 E
Heavy-duty, multi-purpose breakers

These breakers offer heavy-duty breaking in frozen soil, asphalt, and reinforced concrete and are considered to be among the best in their class.

Delivering 81 foot pounds at 1,500 blows/min., the LH 27 and LH 28 E are powerful and highly effective.

They work at a standard flow rate of 8 gpm, and at 5.3 gpm with a simple adjustment.

 

LH 39/40 E
Super heavy-duty breakers

Hitting at 111 foot pounds and delivering 1,275 blows/min., the LH 39 and LH 40 E are among the most powerful handheld breakers in the world.

They are used for the most demanding jobs in heavy asphalt, reinforced concrete, and foundations.

Popular with contractors throughout North America, they often replace mini-excavators with mounted breaker attachments.

Can be used with 8 - 10 gpm power packs.


Vibration-dampening handle
The spring handle provides vibration dampening. In addition, the
handle offers enhanced durability and easy maintenance.

 

LH 23E
 
Keep-clean couplings
LH 23E Hammer

View of Hammer down to Chisel Point

High productivity design

The slim design gives good line of sight to the chisel point to boost productivity. Operator fatigue is reduced due to the well-balanced design and the elimination of external side bolts and machine parts that could come into contact with operator's body.

Keep-Clean Couplings
To keep hydraulic systems clean, hoses are fitted with high quality couplings. They comply with HTMA* standards and feature easy, fast, and safe connections even in industrial and mining applications in which there are high concentrations of dust and dirt.

*Hydraulic Tool Manufacturers' Association

Standard breakers
LH 18
LH 22
LH 27
LH 39
Weight
lb.
41.2
46.1 - 49.8
55.6
71.0
Length
in.
25.1
26.9
29.9
29.9
Oil flow
gpm
5.3
5 - 8
5 - 8
8 - 10
Working pressure
psi
1300 - 1600
1500 - 1800
1500 - 1800
1500 - 1800
Return line pressure max
psi
150
215
215
215
Vibration level (ISO 8662-5)3
H/A
8.3
11.4
11.4
14.2
Impact rate (5 gpm)
blows/min.
1600
1450
1270
 
Impact rate (8 gpm)
blows/min.
 
2160
1860
1150
Impact rate (10 gpm)
blows/min.
     

1500

EHTMA class
C
D (C)1
D (C)1
D (E)2

Breakers with advanced vibro-reduction
LH 19 E
LH 23 E
LH 28 E
LH 40 E
Weight
lb.
42.1
47.0 - 50.7
56.4
71.0
Length
in.
25.1
26.9
29.9
29.9
Oil flow
gpm
5.3
5 - 8
5 - 8
8 - 10
Working pressure
psi
1300 - 1600
1500 - 1800
1500 - 1800
1500 - 1800
Return line pressure max
psi
150
215
215
215
Vibration level (ISO 8662-5)3
H/A
3.5
3.3
3.4
6.0
Impact rate (5 gpm)
blows/min.
1600
1450
1270
 
Impact rate (8 gpm)
blows/min.
 
2160
1860
1150
Impact rate (10 gpm)
blows/min.
     

1500

EHTMA class
C
D (C)1
D (C)1
D (E)2

1 - Can be adjusted to 5 gpm
2 - Can be adjusted to 10 gpm
3 - LH 18/19 E, LH 22/23 E and LH 27/28 E measured at 5 gpm, LH 39/40 E measured at 8 gpm.

The lightweight drill for heavyweight drilling

LHD Hammers in use
LHD 23 M Rock Drill

LHD 23 M rock drill

This lightweight tool is designed for drilling blast, anchor, and rock-splitting holes. It is used by contractors, the military, and utilities who want convenient and efficient drilling without large compressors. With standard integral steel, it drills diameters of up to 2 in. and depths down to approx. 20 ft. by using hydraulic power for impact and rotation. A small additional compressor is needed for flushing.


Rock drill
LHD 23 M
Shank size
Hex (in.)

7/8 x 4 1/4

Weight without hoses and drill
lb.
54
Service weight
lb.
62.4
Oil flow
gpm
5.3 - 6.6
Working pressure
psi
1450 - 2000
Return line pressure max
psi
215
Impact rate
blows/min.
2400 - 3000
Revolutions
rpm
320 - 400
Torque
ft. lb.
48
Direction of rotation
CW*
EHTMA class
C

*Counter clockwise available as option.

Submersible Drainage Pumps

Submersible drainage pumps

Atlas Copco submersible hydraulic pumps are lightweight, compact, and extremely efficient. They are used in a wide range of applications, including continuous pumping of clean or contaminated water on building sites, in flooded excavations, and cellars.

TSubmersible Hydraulic Pumphe pumps are driven by a built-in hydraulic motor and are spark proof. They are cooled and lubricated by the hydraulic oil and can therefore be left to run dry without damage. The pumps offer impressive performance considering their size and weight, providing heads of 82 and 105 ft. and output of 222 - 507 gpm.

The 2-inch pump handles small stones and debris of up to 3/8 in. and is an ideal all-round pump for municipalities, water and waste utilities, and rescue services. It is also widely used in general construction, road services, and maintenance work.

The 3-inch submersible slurry pump can be used in similar applications, but can also handle mud and slurry containing stones and particles of up to 2 1/2 in. in diameter.

Both pumps come with a 32 ft. discharge hose fitted with quick-release couplings for easy handling.


Water pumps
LWP 2
LTP 3
Weight
lb.
23
28
Dimensions H x W
in.
10.5 x 8.5
14.2 x 11.9
Oil flow
gpm
4.8 - 6.4
6.9 - 10.1
Working pressure
psi
1500
2000
Max. working pressure
psi
4000
4200
Pump head max
ft.
82
104
Pump flow max
gpm
222
507
Discharge
in.
2
3
Solid handing up to
in.
3/8
2 1/2
EHTMA class
C
D

Hose for Pump
Description
Length
Connection
Weight
Comments
 
ft.
in.
lb.
 
Hose for 2 inch water pump
32.8
2
7.5
snap-lock quick-release coupling, female
Hose for 3 inch trash pump
32.8
3
8.4
snap-lock quick-release coupling, female
Core Drills in use

Core drills

These powerful drills are ideal for all hand-drilling jobs and where there is no room for drill stands. Where large diameter holes need to be drilled manually, hydraulic core drills are often the only option.

Hydaulic Drill in CaseHydraulic drills give very low kickback when drill bits jam due to the hydraulic control of the drill torque. So operators will always be in control, even when drilling holes up to 8 inches in diameter and greater.

Atlas Copco core drills are used by professionals in a wide range of applications, including building renovation and utility work. They are used to install drainage, sewer and water pipes, plus cable and ventilation ducks where wide, deep holes are needed.

The drills offer spark-free operation - since there are no electrical components - for safe operation inside buildings, in hazardous environments, and even underwater. With its standard round 2.3 in. front-end, you can use Atlas Copco drills with the majority of commonly available drill stands.


Core drills
LCD 5
LCD 10
LCD 15
LCD 24
Weight
lb.
18
18
18
18
Oil flow
gpm
5.3 - 8
5.3 - 8
5.3 - 8
5.3
Length without drill
in.
16
16
16
16
Working pressure
psi
1160 - 2500
1160 - 2500
1160 - 2500
1160 - 2500
Revolutions
rpm
600 - 900
1000 - 1500
1500 - 2200
2400
Drill diameter
in.
3 - 8
2 - 4
1 - 3
0.5 - 1.2
Thread female (drive)*
1/2 " BSP
1/2" BSP
1/2" BSP
1/2" BSP
EHTMA class
C
C
C
C

*1/2" BSP male x 1 1/4 UNC male drive adapter included for use of larger diameter core bits.

Core Drill

  Description
Core bit size
Length
Weight
Drilling Material
   
in. in dia.
in.
lb.
 
Bit Diamond core bit
2.4
17.7
3.8
Concrete, reinforced concrete, and brickwork
Diamond core bit
3.2
17.7
5.3
Concrete, reinforced concrete, and brickwork
Diamond core bit
4
17.7
7.1
Concrete, reinforced concrete, and brickwork
Diamond core bit
4.4
17.7
8.2
Concrete, reinforced concrete, and brickwork
Diamond core bit
5.2
17.7
10.1
Concrete, reinforced concrete, and brickwork
Diamond core bit
6
17.7
13.2
Concrete, reinforced concrete, and brickwork
Diamond core bit
6.4
17.7
13.9
Concrete, reinforced concrete, and brickwork
Bit
Diamond core bit
7.9
17.7
21.9
Concrete, reinforced concrete, and brickwork
Drill chuck for steel and wood drilling  
3.9
.9

Chuck 0.06 - 0.51 in. Adapter 1/2 in. bsp to 3/8 bsp

Handheld Post Equipment

Handheld Post Hole Borer and Post Pullers in use

Handheld post hole borer

Compact and powerful, this tool drills holes in hard soil and sand of up to 4 ft. in depth and 3.5 - 14 in. in diameter. It offers reversible rotation and is designed for two-person operation.

All augers have interchangeable bits for increased service lifetime. The auger is ideal for fence installation and tree planting.

It can also be used to open and close main water line valves with the help of special adaptors.

Handheld Post Hole Borer
 

Post puller

The Atlas Copco post puller is used by road-maintenance contractors to remove damaged crash barriers and road signs.

With hardened jaws and an automatic chain-tightening clamp, this post puller is ideal for removing all kinds of wooden or steel posts, including IPE, HPE, UPE profiles and round/square steel tubes.

This post puller develops 13,228 lbs. of hydraulic pulling force. With the help of a separate hand lever (optional), you can boost the pulling force by an extra 8818 lbs. to loosen any poles that are fixed into place with ease.

Weighing just 132 lbs., it is the most compact and portable pulling device on the market -- perfect for on-site road repairs that cannot be accessed by heavy vehicles with a 10-ton crane.

Post Puller

Handheld post hole borer
LPHB
  Post puller
LPP 10 HD
Weight without auger
lb.
44
Weight
lb.

132

Oil flow
gpm
4 - 8
Oil flow
gpm
5 - 10
Working pressure
psi
1100 - 2150
Max working pressure
psi
2320
Max back pressure
psi
725
Max back pressure
psi
435
Torque
ft./lbs.
232
Lift capacity per stroke
in.
0.5 - 8
Speed rotation
rpm
90 - 188
Pulling force
lb.
13,228
Auger size at L=34
in.
3.5 - 13.8
Full pulling force
lb.
22,045
EHTMA class
C/D
EHTMA class
C/D

Post drivers

Used for driving in road barrier tubes, profiles signposts, fences, and a wide range of anchors. The post drivers provide stable, powerful, high speed driving for a variety of post sizes. When operated with an optional hose-mounted remote-controlled valve, the drivers can be run with both open- or closed-center systems.

The LPD-T comes with a standard 1.6 ft. quick-release coupler tail hose and has a built-in paddle trigger that the operator activates directly on the driver.

The LPD-RV is supplied with 6.5 ft. long tail hose and features a remote on/off valve that allows the operator to activate the driver even when it is placed on top of tall posts.

Post Driver in use

Post drivers
LPD-T
LPD-RV
LPD-T Post Driver
Activation type
By trigger lever
By remote valve
Hydraulic system
Open center
Open- or closed-center
Weight
lb.
68
64
Weight with hoses
lb.
75
71
Max working pressure
psi
2000
2000
Oil flow
gpm
5 - 8
5 - 8
Impact rate at 8 gpm
blows/min.
1500
1500
Hydraulic ports
1/2" BSP
1/2" BSP
EHTMA class
C/D
C/D

Post driver adapter choices: universal, round, and square.

Cut-off saws

Power tools in use

The best power-to-weight

Construction and rental companies around the world are discovering the advantages of using hydraulics. They know that hydraulic equipment offers the best power-to-weight ratio of any system. And they appreciate that a hydraulic power pack is small and light enough so that two people can lift one up and fit it in the back of a van.

A real cost advantage

Construction and rental companies have been quick to understand the very real cost advantage of hydraulics. For the price of one compressor/breaker combination, you can buy two complete hydraulic power pack/breaker sets. In fact, you might not need a power pack at all. With the help of an oil flow divider and an extension hose, you can hook hydraulic tools directly to a hydraulic-powered carrier. Hydraulic power packs are a flexible power source. Use them to power cutoff saws, core drills, and submersible pumps. You can use hydraulic tools anywhere, independent of electric or pneumatic supply. With no exhaust, you can put them to work indoors and out. And they can be used whether it's hot or cold, dusty or wet, or even underwater.

Raw power, smooth action

The first time you use a hydraulic tool, you're in for a surprise. Here's this compact, light tool...and it out performs any other comparable tool. With the hydraulic cut-off saw or core drill you get all the raw power of a power pack transmitted directly into these small, lightweight tools. A 16-inch saw, for example, runs at full throttle with all the power of an 18 hp engine and yet it weighs just 22 - 24 lbs. because with hydraulics you get direct drive from motor to blade. Hydraulic-powered tools are also easy to use. Due to the smooth supply of power you get a minimum of kick back and low vibrations.

Easy to own

There is not much that can go wrong with an Atlas Copco hydraulic tool. With just one or two moving parts -- lubricated continuously by the hydraulic oil -- there's minimal wear and very few parts to replace. Hydraulics are reliable by nature. Working in a closed loop, dirt and moisture are kept out. And with no-spill, flat-face couplings, it's easy to keep the system clean and to ensure correct connection.


Cut-Off Saw
Cut-off Saw on Cart

These powerful, lightweight, and compact saws can be used to cut through concrete, asphalt, and steel. Their simple hydraulic design with direct drive reduces maintenance, especially in comparison with belt-driven saws. They are easy to use even under the most demanding conditions due to the open cutting face. With a lightweight cart you can use the saws for floor, road, and other light surface jobs.

Technical Data

Cut-off saws
LS 14
LS 16
Weight
lb.
21.6
23.4
Oil flow
gpm
5 - 8
5 - 10
Max oil pressure
psi
2500
2500
Revolutions
rpm
2500 - 4000
2000 - 4000
Speed
ft./s
151 - 246
138 - 279
Blade size
in.
14
16
Arbor size
in.
1
1
Cutting depth
in.
5.3
6.3
EHTMA class
C/D
C/D

Cart for 14 inch and 16 inch cut-off saw

Cut-off Saw on Cart
Description
Weight
Comments
 
lb.
 
LSC cart for cut-off saw
55.12
incl. water kit

Diamond blades for 14 inch and 16 inch cut-off saw

  Description
Blade size
Arbor hole diameter
Weight
Comments
   
in.
in.
lb.
 
Diamond Blade
Concrete diamond blade
14
1
3.6
Cutting concrete and concrete reinforcement
Concrete diamond blade
16
1
5.1
Cutting concrete and concrete reinforcement
Diamond Blade
Asphalt diamond blade
14
1
3.6
Cutting asphalt
Asphalt diamond blade
16
1
5.8
Cutting asphalt

Gas, diesel, or electric-driven power packs

Lightweight, compact, and portable

These well-proven power packs are the ideal power source for a wide range of applications in the 5 - 10 gpm / 2500 psi range. Lightweight and compact, they are easy to store and transport. Equipped with wheels and handle, they are easy to move around construction sites.

Reduce fuel consumption and noise

All 5 - 8 gpm gasoline power packs are equipped with Power on Demand (POD). This hydraulic regulatory system automatically idles the engine when the tool is not being used and speeds it up when the tool is activated.

Efficient cooling

The thermostatically controlled oil cooler allows quick warm-ups and helps protect the hydraulic oil from overheating. Correct working temperature is achieved within minutes -- even during the winter.

 

 

Hydraulic LP 9-20 P Power Pack
 
On/Off Valve

On/off valve
Easy tool change and slow start up with the variable flow on/off valve.

Filter Indicator

Foldable handles

One person can move power packs around site with ease.

 

Filter indicator
All power packs feature a large, easy-to-read filter gauge that indicates when it is time to change the filter.


Power packs
LP 9-20 P
LP 9-20 E
LP 13-20 DEL
LP 13-30 P
Engine

9 HP
Honda gasoline

5.5 kW / 3x400 V
/ 16 A
Electric

10 HP
Lombardini diesel

13 HP
Honda gasoline

Weight (incl. oil)
lb.
163
154
256
201
Dimensions (LxWxH)
in.
23x21x27
23x21x27
28x24x29
28x24x29
Oil flow
gpm
5
5
5
5 - 8
Maximum pressure
psi
2200
2000
2000
2200
Fuel capacity
gal.
1.59
 
1.45
1.72
EHTMA class
C
C
C
C/D
Hose included
YES
NO
NO
YES
Power on Demand (POD)
YES
NO
NO
YES
Oil control: engine oil
YES
NO
NO
YES
Electric start
NO
YES
YES
NO

Power packs
LP 18-30 PE
LP 18-40 PE
LP 18 Twin E*
LP 18 Twin PE*
Engine

18 HP
B&S Vanguard
gasoline

18 HP
B&S Vanguard
gasoline

11 kW / 3x400 V
/ 32 A
Electric

18 HP
B&S Vanguard gasoline

Weight (incl. oil)
lb.
243
243
271
243
Dimensions (LxWxH)
in.
28x28x29
28x28x29
28x24x29
28x28x29
Oil flow
gpm
5 - 8
5 - 10
2x5 / 1x10
2x5 / 1x10
Maximum pressure
psi
2500
2200
2200
2200
Fuel capacity
gal.
1.90
1.90
 
1.90
EHTMA class
C/D
C/D/E
C/E
C/E
Hose included
NO
NO
NO
NO
Power on Demand (POD)
NO
NO
NO
NO
Oil control engine oil
NO
NO
NO
NO
Electric start
YES
YES
YES
YES

*Version with twin and single configuration and different flow and pressure settings also available.

Accessories

At Atlas Copco we maintain a wide range of accessories -- highly productive, efficient tools need the right consumables and parts. Our accessory range is ever expanding in line with new applications.

Water kit

Diamond blades and core bits need a small but constant supply of water to flush away slurry and to repress dust. Where water is available, taps can be used and water flow can be regulated on the tool. Where there is no water supply, we recommend the Atlas Copco water kit, a small pressurized water container.

Water Kit
Description
Size
(W x H x D)
Water
volume
Weight
Comments
 
in.
g
lb.
 
Water kit with pressure tank
8.7x24.4x9.8
2.6
17.7

Water supply for LCD
core-drill
and LS cut-off saw

Oil flow divider

The oil flow divider allows you to run tools from hydraulic-powered carriers by reducing flow and pressure. An extension hose is required to connect the divider to the tool.

Type  
LFD 20
LFD 30
Oil Flow Divider
Max oil flow rate in
g/min.
15.9
31.0
Regulated oil flow rate
g/min.
5.3 - 6.6
6.0 - 10
EHTMA class
C
D

Extension hoses

By adding one or two 23 ft. extension hoses you can use up to 69 ft. of hose with no significant drop in pressure. The hoses are light and flexible and are fitted with flat-face, quick-release couplings. (Extension hoses come as standard with LP 9-20 P and LP 13-30 P).

Length
m
23
39.4
Extension Hoses

Couplings: flat face
quick release

dimension
1/2"
1/2"
EHTMA class
C/D
C/D

Power Pack BIO-OIL

Each power pack comes with two 1-gallon bottles of Atlas Copco biodegradable oil, enough for filling the power pack and 23 ft. hose.

*Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.

A wide range of top quality steel

At Atlas Copco, we maintain a comprehensive range of steel so that you can select the right tool for the job.

Atlas Copco steel is among the hardest wearing on the market. A controlled heat treatment process imparts both strength and high wear resistance to deep surface layers while maintaining a tough, shock resistant central core that resists breakage.

The impact face is milled, resulting in better contact between the piston and the tool, improved transfer of energy, as well as less vibration and wear on both hammer and chisel.

Tool Length and Width measurements
Tool View
Flat to Flat
Tool View
Point to Flat
7/8 x 3 1/4 in.
1 x 4 1/4 in.
1 1/8 x 6 in.
1 1/4 x 6 in.
W (in.)
L (in.)
W (in.)
L (in.)
W (in.)
L (in.)
W (in.)
L (in.)
Moil point  
14
 
15
 
14
 
14
   
18
 
18
 
18
 
18
   
24
 
24
 
24
 
24
   
36
 
36
 
36
 
36
Narrow chisel
1
14
1 1/8
15
1 1/4
14
1 3/8
14
 
1
18
1 1/8
18
1 1/4
18
1 3/8
18
 
1
24
1 1/8
24
1 1/4
24
1 3/8
24
 
1
36
1 1/8
36
1 1/4
36
1 3/8
36
Wide chisel
3
14
3
15
3
15
3
15
 
3
18
3
18
3
18
3
18
 
3
24
3
24
3
24
3
24
Wedge chisel
1 3/8
15
2
15
2
16
2

16

Digging chisel
3
14
3
15
3
15
3
15
Asphalt cutter
4 3/4
13
4 3/4
13
5
13
5
13
Clay spade
5
17
5
16
5 1/2
15
5 1/2
15
Shank for pad  
8
 
11
 
9
 
9
Tamping pad, round
7
 
7
 
7
 
7
 
Tamping pad, square
7
 
7
 
6
 
6
 
Tamping pad, square        
8
 
8
 
Stake driver
2 1/2 ID
 
2 1/2 ID
 
2 1/2 ID
 
2 1/2 ID
 
Stake driver
3 ID
 
3 ID
 
3 ID
 
3 ID
 
Stake driver shank  
9
 
9
 
9
 
9

*Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.