AC Distributor GooglePlus
Flags
Flags
Facebook

America West Drilling Supply Utility Power Pole Drill

America West's truck-mounted power pole drill is a much preferred and cost-effective method for drilling large diameter power pole holes. The combination of our Missile LXQ down the hole hammer and our efficient bit design makes this the ideal package for drilling large diameter holes suited to the Utility industry.

       Available hole sizes:  12”, 14”, 18”, 20”, 22”, and 24”
Power pole drill

Features and Benefits

  • Air Consumption - 804 scfm at 100 psi and 1028 scfm at 125 psi.

  • Oil/Lubrication - 2 Pints per 100 cfm per hour / measured up to 1000 cfm.

  • Rotation Speed/Torque on Head - 10 to 20 RPM.

  • Drilling Depth - 84" Standard; custom extension rods available for other depths.
Power pole drill
Power pole drill in action
Power pole drill setting pole

Technical Specifications
Description
Outer Diameter
Overall Length
Minimum
Hole Size
Maximum
Hole Size
Overall Weight
Percussive pole drill with air swivel and
2 5/8" hex drive
11.21"
118'
12.25'
24"
2243 lbs.
16.75" accelerator shroud for hole diameters greater than 17.25"
16.75"
73.23"
17.25"
24"
1080 lbs.
20" accelerator shroud for hole diameters greater than 20.50"
20"
73.23"
20.5"
24"
1790 lbs.
22" accelerator shroud for hole diameters greater than 22.50"
22"
73.23"
22.5"
24"
2337 lbs.
Extension rod 72"
9.92"
82.12"
   
1051 lbs.
Air control, lubricator, and liquid injection support module        
580 lbs.
Sustainability kit QL 120 hammer Valve Assembly, O-Ring Check Valve, Bearing Retaining Ring, and O-Rings


Request info


Air Consumption Chart
PSI
100
150
200
250
300
350
CFM
750
1,125
1,675
1,925
2,475
2,960


Power Pole Drill Set

Power Pole Drill Set

Component Part
Item #
Description
Quantity
1
Swivel and Shock Absorber
1
2
Shroud
1
2-1
Locking Pin
2
2-2
Locking Bolt
4
3
12" Hammer with QL120 Shank
1
4
22" Bit for QL120 Shank
1
4-1
QL120 Foot Valve
1

dfasdfsd

Air Swivel with Cushion Device

Air Swivel with Cushion Device

Component Part
Item #
Description
Quantity
1
Tube
1
2
V-Packing Bushing 01 (1 ea)
2
3
V-Packing (3 ea)
4
4
V-Packing Bushing 02 (1 ea)
2
5
V-Packing Bushing 03 (1 ea)
1
6
V-Packing Bushing 04
1
7
Snap Ring
1
8
Bearing
1
8-1
Bearing
1
9
Oil Seal
1
10
Oil Seal
1
11
Flange 01
1
12
Flange 02
1
13
Hexagon Head Bolt (12 ea)
2
14
Cushion Device
1
15
Locking Pin
2
16
Locking Bolt
4
17
Cushion Packing (urethane)
1
18
API 6 5/8" REG Female Joint
1
 




Application
Connection
Excavator

RS-12 / Single Speed unit

Anchor
H-250
11T-17T

Accessories

  • Universal Mounting Plate for Skid-Skeer
  • Long Reach Universal Mount for Skid-Skeer
  • TruLink Class 1 4" Monitor
  • TruLink Class 1 8" Monitor
  • Link Arm 45mm
  • Pin Assembly 45mm
RS-12 / Single Speed diagram

RS-12 / Single Speed - Specifications

Total Unit Weight
546 lbs.
 
Reference Torque Chart
Hydraulic Motor Information
Pressure (psi)
Torque (ft/lbs)
Displacement 23.9 cu/in
1600
6941
Motor Type Single Speed Bi-Directional
1800
7808
Motor Output Shaft 1 1/2" Spline 17T
2000
8677
Motor Mount SAE - C 4 Bolt
2200
9544
Motor Ports 1 1/16" 12 O-Ring
2400
10,411
Cross-Over Pressure Relief Set @ 3100 psi
2600
11,280
Planetary Gearbox Information
2800
12,147
Gearbox Type Planetary Two Stage
3000
13,014
Reduction Ratio 17.39:1
Reference Speed Chart
Output Shaft 2 1/2" Hex
Flow (gpm)
Speed (rpm)
Oil Capacity 1.7 Gallons
15
7
Oil Type SAE 80W90 GL-5
20
9
Shaft Pull Out (lbs.) 22,500 lbs.
25
11
NOTE: Revolution Drive units are not recommended for DTH and will not be covered under warranty for damage due to down-the-hole drilling.
30
13
35
15
40
18

Output speed and torque specifications are NOT listed at 100% efficiency. Maximum efficiencies have been applied to the torque and speed charts according to the manufacturer's recommendations. Speed and torque output are dependent on the overall system efficiencies associated with the prime mover's hydraulic system. When the purchaser is determining criteria for specific applications, please contact the manufacturer. The manufacturer has made every attempt to present accurate and suitable information. This web page should be used for information and comparative purposes only. When application-specific information is required, please contact the manufacturer.



Pneumatic Oiler

Oiler (Recommended for use with Power Pole Drill)

Maximum Operating Pressure:

  • 7 and 12 gallon - 600 psi
  • 17 and 33 gallon - 1,000 psi

Sizes:

  • 7 gallon - 600 psi
  • 12 gallon - 600 psi
  • 17 gallon - 1,000 psi
  • 33 gallon - 1,000 psi

Features:

  • Easy to remove cap
  • No moving parts
  • No pumps
  • No wiring
  • Venturi style
  • Infinite flow control with needle valve
  • Manifold can be removed from tank and mounted remotely
  • Sight glass
  • Pressure vessel (A.S.M.E. Code Stamped)
  • 2" or 3" manifold
  • Fill while you drill
  • Fits any drill rig

Manifold needs to be mounted at lubricator bracket level or lower.

Blue line

Related Products