G-Force GFR6000 IR360 Shank

Hammer Specifications - G-Force IR360 Shank

Features:

Easy to service
Special heat-treated alloy piston for long life, Rockwell hardness 60
Minimum loss of performance when injecting foam or water

Item #	Description	Part #
1	Back Head	G6001
2	Back Head O-Ring	G6002
3	Choke
4	Air Check Valve	G6004
5	Air Check Valve Spring	G6005
6	Spacer Tube	G6006
7	Air Distributor	G6007
8	Air Distributor O-Ring	G6008
9	Cylinder	G6009
10	Cylinder Stop Ring	G6010
11	Wear Sleeve	G6011
12	Piston	G6R6012
13	Piston Stop Ring	G6R6013
14	Bit Bearing O-Ring	G6R6014
15	Bit Bearing	G6R6015
16	Bit Retaining O-Ring	G6R6016
17	Bit Retaining Ring	G6R6017
18	Chuck (Drive Sub)	G6R6018
	Choke Plug Kit	G6029
	O-Ring Kit	G6030

Specifications

Length (w/o drill bit)	53.42"
Outside Diameter	5.41"
Weight (w/o bit)	219.7 lbs.
Cylinder Bore	4.496"
Piston O.D.	4.491"
Piston Stroke	3.93"
Piston Weight	26 lbs.
Hole Sizes	6" - 8"
Air Pressure Consumption	100 psi - 350 psi
Wrench Size	A/F 3.968"
Connection	Std. 3 1/2" API Reg Pin

Air Consumption Chart

PSI	150	200	250	300	350	400
CFM with blank choke	350	565	720	875	995	1,130
with 1/8" choke	375	595	760	925	1,060	1,205
with 1/4" choke	425	665	845	1,095	1,270	1,350

All Hammers come Fitted with Blank Choke located in the Air Check Valve

Click here to download brochure

Hammer Service Log

Wear Sleeve / Piston Clearance

Part	New Dimension		Discard Clearance
Wear Sleeve	A	4.496"	greater than or equal to 0.010"
Piston OD	B	4.491"	greater than or equal to 0.010"

Inner Cylinder / Piston Clearance

Part	New Dimension		Discard Clearance
Cylinder ID	C	3.75"	greater than or equal to 0.010"
Piston OD	D	3.745"	greater than or equal to 0.010"

Distributor Probe / Piston ID Clearance

Part	New Dimension		Discard Clearance
Distributor Probe OD	F	1.328"	greater than or equal to 0.010"
Piston ID	E	1.336"	greater than or equal to 0.010"

External Wear

Description	Wear Limit
Wear Sleeve Reverse Dimension	5.118"
Wear Sleeve Discard Dimension	4.96"
NOTE: If no evidence of significant air pressure drop or if wear sleeve is wearing evenly on the top and bottom end, recommendation is to not reverse wear sleeve. Chuck should be replaced when wear transfers to wear sleeve.

Lubrication

G-Force Series Hammers are precision-made tools and should be treated as such. Only the highest quality lubrication should be used and a constant flow of oil must be maintained at all times. Recommended lubrication amount 1/3 Pint per 100 cfm per hour.

Recommended Grades of Lubricant

ESSO
MATEX
CASTROL
SHELL
MOBILE

AROX EP 150
RDO 302
RD OIL DP 100
AIR TOOL OIL 2 A 320
ALMO NO. 5

Heavy duty oil is recommended for all year-round use, in particular where air supply to the hammer is at high temperature. If lighter grade oil is required due to very low ambient temperatures, amount of oil being used should be increased by 30 percent.

Recommended Pull Down

Minimum @ 100 psi - 1500 lbs.

Maximum @ 350 psi - 4000 lbs.

Missile Warranty will be voided by the following:

Welding on Wear Sleeve.
Heating Case with a Torch.
Gripping Wrenches across Threads.
Hammering on Casing.

READ WARNING LABEL ATTACHED TO HAMMER.