Missile LXQ Series - LXQM8000 SD8 Shank

Hammer Specifications - LXQ SD8 Shank

Features:

Easy to service
Special heat-treated alloy piston for long life, Rockwell hardness 60
Minimum loss of performance when injecting foam or water

Item #	Description	Part #
1	Back Head	LQ8001
2	Back Head O-Ring	LQ8002
3	Choke
4	Air Check Valve	LQ8004
5	Air Check Valve Spring	LQ8005
6	Make-Up Rubber (Buffering)	LQ8006
7	Air Distributor	LQ8007
8	Air Distributor O-Ring	LQ8008
9	Cylinder	LQ8009
10	Wear Sleeve	LQM8010
11	Piston	LQM8011
12	Piston Stop Ring	LQM8012
13	Bit Retaining O-Ring	LQM8013
14	Bit Retaining Ring	LQM8014
15	Chuck (Drive Sub)	LQM8015
	Choke Plug Kit	LQ8029
	O-Ring Kit	LQ8030

Specifications

Length (w/o drill bit)	55.41"
Outside Diameter	7.007"
Weight (w/o bit)	424.05 lbs.
Cylinder Bore	5.824"
Piston O.D.	5.821"
Piston Stroke	3.93"
Piston Weight	84.3 lbs.
Hole Sizes	8" - 10"
Air Pressure Consumption	100 psi - 350 psi
Wrench Size	A/F 5.512"
Connection	Std. 4 1/2" API Reg Pin

Air Consumption Chart

PSI	150	200	250	300	350	400
CFM with blank choke	434	621	800	975	1,149	1,290
with 1/8" choke	465	651	843	1,025	1,225	1,350
with 1/4" choke	534	708	949	1,151	1,390	1,425

All Hammers come Fitted with Blank Choke located in the Air Check Valve

Click here to download brochure

Hammer Service Log

Wear Sleeve / Piston Clearance

Part	New Dimension		Discard Clearance
Wear Sleeve	A	5.827"	greater than or equal to 0.010"
Piston OD	B	5.822"	greater than or equal to 0.010"

Inner Cylinder / Piston Clearance

Part	New Dimension		Discard Clearance
Cylinder ID	C	4.803"	greater than or equal to 0.010"
Piston OD	D	4.797"	greater than or equal to 0.010"

Distributor Probe / Piston ID Clearance

Part	New Dimension		Discard Clearance
Distributor Probe OD	F	1.765"	greater than or equal to 0.010"
Piston ID	E	1.772"	greater than or equal to 0.010"

External Wear

Description	Wear Limit
Wear Sleeve Discard Dimension	6.693"
NOTE: Chuck should be replaced when wear transfers to wear sleeve.

Lubrication

LXQ Series Hammers are precision-made tools and should be treated as such. Only the highest quality lubrication should be used and a constant flow of oil must be maintained at all times. Recommended lubrication amount 1/3 Pint per 100 cfm per hour.

Recommended Grades of Lubricant

ESSO
MATEX
CASTROL
SHELL
MOBILE

AROX EP 150
RDO 302
RD OIL DP 100
AIR TOOL OIL 2 A 320
ALMO NO. 5

Heavy duty oil is recommended for all year-round use, in particular where air supply to the hammer is at high temperature. If lighter grade oil is required due to very low ambient temperatures, amount of oil being used should be increased by 30 percent.

Recommended Pull Down

Minimum @ 100 psi - 1500 lbs.

Maximum @ 350 psi - 4000 lbs.

Missile Warranty will be voided by the following:

Welding on Wear Sleeve.
Heating Case with a Torch.
Gripping Wrenches across Threads.
Hammering on Casing.

READ WARNING LABEL ATTACHED TO HAMMER.