Missile LXQ Series - LXQM15000-H H150 Shank

Missile LXQ H150 diagram

Features:
  • Easy to service
  • Special heat-treated alloy piston for long life, Rockwell hardness 60
  • Minimum loss of performance when injecting foam or water

Item # Description Part #
1 Back Head LQ1501H
2 Back Head O-Ring LQ1502H
3 Back Head Washer  
4 Choke LQ1504H
5 Air Check Valve LQ1505H
6 Air Check Valve Spring LQ1506H
7 Buffering Washer LQ1507H
8 Buffering Ring LQ1508H
9 Air Distributor LQ1509H
10 Air Distributor O-Ring LQ1510H
11 Cylinder LQ1511H
12 Wear Sleeve LQ1512H
13 Piston LQ1513H
14 Piston Stop Ring LQ1514H
15 Bit Retaining O-Ring LQ1515H
16 Bit Retaining Ring LQ1516H
17 Chuck Washer LQ1517H
18 Chuck LQ1518H
19 Drive Pin LQ1519H
  Choke Plug Kit LQ1529H
  O-Ring Kit LQ1530H

Specifications


Length (w/o drill bit) 69.41"
Outside Diameter 12.6"
Weight (w/o bit) 1,878 lbs.
Cylinder Bore 9.449"
Piston O.D. 9.442"
Piston Stroke 4.92"
Piston Weight 338.19 lbs.
Hole Sizes 15" - 20"
Air Pressure Consumption 100 psi - 250 psi
Wrench Size -
Connection Std. 8 5/8" API Reg Pin

Air Consumption Chart


PSI 100 150 200 250 300 350
CFM with blank choke 800 1,100 1,650 2,110 - -
with 1/8" choke - - - - - -
with 1/4" choke - - - - - -

All Hammers come Fitted with blank Choke located in the Air Check Valve




Hammer Service Log


Wear Sleeve / Piston Clearance

Part New Dimension Discard Clearance
Wear Sleeve A 9.449" greater than or equal to 0.010"
Piston OD B 9.442"
Wear Sleeve / Piston Clearance diagram

Inner Cylinder / Piston Clearance

Part New Dimension Discard Clearance
Cylinder ID C 7.874" greater than or equal to 0.010"
Piston OD D 7.867"
Inner Cylinder / Piston Clearance diagram

Distributor Probe / Piston ID Clearance

Part New Dimension Discard Clearance
Distributor Probe OD F 2.551" greater than or equal to 0.010"
Piston ID E 2.559"
Distributor Probe / Piston ID Clearance diagram

External Wear

Description Wear Limit
Wear Sleeve Discard Dimension 0.00"
NOTE:
Chuck should be replaced when wear transfers to wear sleeve.


Lubrication

G-Force Series Hammers are precision-made tools and should be treated as such. Only the highest quality lubrication should be used and a constant flow of oil must be maintained at all times. Recommended lubrication amount 1/3 Pint per 100 cfm per hour.

Recommended Grades of Lubricant

ESSO
MATEX
CASTROL
SHELL
MOBILE
AROX EP 150
RDO 302
RD OIL DP 100
AIR TOOL OIL 2 A 320
ALMO NO. 5
Heavy duty oil is recommended for all year-round use, in particular where air supply to the hammer is at high temperature. If lighter grade oil is required due to very low ambient temperatures, amount of oil being used should be increased by 30 percent.

Recommended Pull Down

Minimum @ 100 psi - 0000 lbs. Maximum @ 350 psi - 0000 lbs.

Missile Warranty will be voided by the following:


Welding on Wear Sleeve.
Heating Case with a Torch.
Gripping Wrenches across Threads.
Hammering on Casing.

READ WARNING LABEL ATTACHED TO HAMMER.